Kismet Wireless

Kismet Forums

 

Posted by:iturk
Subject:Arptype 24 not supported by libpcap !!
Date:04:13:28 22/10/2006


Hi there i am having a problem starting my kismet here is the log:

$ sudo kismet
Password:
Server options: none
Client options: none
Starting server...
Waiting for server to start before starting UI...
Suid priv-dropping disabled. This may not be secure.
No specific sources given to be enabled, all will be enabled.
Enabling channel hopping.
Enabling channel splitting.
Source 0 (Prism): Enabling monitor mode for wlanng source interface eth1 channel 6...
Source 0 (Prism): Opening wlanng source interface eth1...
**************************************************************************
FATAL: arptype 24 not supported by libpcap - falling back to cooked socket
**************************************************************************

I am runnin Ubuntu with 2.6.16.20 WEST 2006 i686 GNU/Linux

The version of libpcap that i am using is 0.9.4.1.
The version of kismet is 2005.08.R1.

My Wireless card its a -> Intersil Corporation Intersil ISL3890 [Prism GT/Prism Duette] >> (And it works fine has eth2) !!

Also i have this in my dmesg:

SDT (v001 ASUS D1 0x42302e31 MSFT 0x31313031) @ 0x1dffb000
ACPI: FADT (v001 ASUS D1 0x42302e31 MSFT 0x31313031) @ 0x1dffb0c0
ACPI: BOOT (v001 ASUS D1 0x42302e31 MSFT 0x31313031) @ 0x1dffb030
ACPI: MADT (v001 ASUS D1 0x42302e31 MSFT 0x31313031) @ 0x1dffb058
ACPI: DSDT (v001 ASUS D1 0x00001000 MSFT 0x0100000b) @ 0x00000000
ACPI: PM-Timer IO Port: 0xe408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 128, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 20000000 (gap: 1e000000:e0c00000)
Built 1 zonelists
Kernel command line: BOOT_IMAGE=Kernel_2.6.16 ro root=306
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 2000.420 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 481512k/491500k available (3288k kernel code, 9416k reserved, 1364k data, 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4006.48 BogoMIPS (lpj=8012970)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 128K
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
CPU: Intel(R) Celeron(R) CPU 2.00GHz stepping 09
Checking 'hlt' instruction... OK.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf10f0, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 *6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Enabling SiS 96x SMBus.
PCI: Ignoring BAR0-3 of IDE controller 0000:00:02.5
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:02: ioport range 0xe400-0xe47f could not be reserved
pnp: 00:02: ioport range 0xe480-0xe4ff has been reserved
pnp: 00:02: ioport range 0xe600-0xe61f has been reserved
pnp: 00:02: ioport range 0x480-0x48f has been reserved
pnp: 00:0c: ioport range 0x3f0-0x3f1 has been reserved
pnp: 00:0c: ioport range 0x290-0x297 has been reserved
pnp: 00:0c: ioport range 0x280-0x287 has been reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:01:00.0
PCI: Bridge: 0000:00:01.0
IO window: d000-dfff
MEM window: df800000-dfffffff
PREFETCH window: e8000000-f3ffffff
PCI: Bus 2, cardbus bridge: 0000:00:10.0
IO window: 00001000-000010ff
IO window: 00001400-000014ff
PREFETCH window: 20000000-21ffffff
MEM window: 22000000-23ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 16 (level, low) -> IRQ 16
Simple Boot Flag at 0x3a set to 0x1
Machine check exception polling timer started.
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.26 [Flags: R/W].
fuse init (API version 7.6)
JFS: nTxBlock = 3763, nTxLock = 30106
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
sisfb: Video ROM found
sisfb: Video RAM at 0xe8000000, mapped to 0xdea80000, size 32768k
sisfb: MMIO at 0xdf800000, mapped to 0xe0ac0000, size 128k
sisfb: Memory heap starting at 32160K, size 32K
sisfb: Detected SiS302LV video bridge
sisfb: Detected 1024x768 flat panel
sisfb: Detected LCD PDC 0x08 (for LCD=CRT2)
sisfb: Detected LCD PDC1 0x08 (for LCD=CRT1)
sisfb: Default mode is 1024x768x8 (60Hz)
sisfb: Initial vbflags 0x8000012
Console: switching to colour frame buffer device 128x48
sisfb: 2D acceleration is enabled, y-panning enabled (auto-max)
fb0: SiS 650 frame buffer device version 1.8.9
sisfb: Copyright (C) 2001-2005 Thomas Winischhofer
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
Asus Laptop ACPI Extras version 0.29
D1 model detected, supported
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
lp: driver loaded but no devices found
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected SiS 650 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
[drm] Initialized drm 1.0.1 20051102
SyncLink PC Card driver $Revision: 4.34 $
SyncLink PC Card driver $Revision: 4.34 $, tty major#253
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)]
lp0: using parport0 (interrupt-driven).
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
nbd: registered device at major 43
b44.c:v0.97 (Nov 30, 2005)
ACPI: PCI Interrupt 0000:00:0f.0[A] -> GSI 18 (level, low) -> IRQ 17
eth0: Broadcom 4400 10/100BaseT Ethernet 00:0c:6e:84:a2:0a
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Loaded prism54 driver, version 1.2
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:02.5
ACPI: PCI Interrupt 0000:00:02.5[A] -> GSI 16 (level, low) -> IRQ 16
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
ide0: BM-DMA at 0xa400-0xa407, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xa408-0xa40f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: IC25N040ATMR04-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: QSI CD-RW/DVD-ROM SBW-241, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 78140160 sectors (40007 MB) w/1740KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 hda6 hda7 >
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.20 loaded.
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt 0000:00:02.3[B] -> GSI 17 (level, low) -> IRQ 18
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[18] MMIO=[df000000-df0007ff] Max Packet=[2048] IR/IT contexts=[4/6]
video1394: Installed video1394 module
ieee1394: raw1394: /dev/raw1394 device initialized
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
INFTL: inftlcore.c $Revision: 1.19 $, inftlmount.c $Revision: 1.18 $
slram: not enough parameters.
ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 19
ehci_hcd 0000:00:03.3: EHCI Host Controller
PCI: cache line size of 128 is not supported by device 0000:00:03.3
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:03.3: irq 19, io mem 0xdd000000
ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 20
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.0: irq 20, io mem 0xde800000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 21
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:03.1: irq 21, io mem 0xde000000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 22
ohci_hcd 0000:00:03.2: OHCI Host Controller
ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:03.2: irq 22, io mem 0xdd800000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v2.3
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
it87: Found IT8705F chip at 0x290, revision 2
wbsd: Winbond W83L51xD SD/MMC card interface driver, 1.5
wbsd: Copyright(c) Pierre Ossman
Advanced Linux Sound Architecture Driver Version 1.0.11rc2 (Wed Jan 04 08:57:20 2006 UTC).
ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 17
intel8x0_measure_ac97_clock: measured 52724 usecs
intel8x0: clocking to 48000
ALSA device list:
#0: SiS SI7012 with ALC650E at 0x9400, irq 17
oprofile: using NMI interrupt.
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 4
input: AT Translated Set 2 keyboard as /class/input/input0
NET4: DECnet for Linux: V.2.5.68s (C) 1995-2003 Linux DECnet Project Team
DECnet: Routing cache hash table of 1024 buckets, 8Kbytes
NET: Registered protocol family 12
ieee80211: 802.11 data/management/control stack, git-1.1.7
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ieee80211_crypt: registered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'WEP'
ieee80211_crypt: registered algorithm 'CCMP'
ieee80211_crypt: registered algorithm 'TKIP'
p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available
Using IPI Shortcut mode
ACPI wakeup devices:
LID PCI0 PCI1 PS2K PS2M USB0 USB3 USB1 USB2 AC97
ACPI: (supports S0 S1 S3 S4 S5)
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
kjournald starting. Commit interval 5 seconds
Freeing unused kernel memory: 196k freed
Synaptics Touchpad, model: 1, fw: 5.9, id: 0xa54ab1, caps: 0x804713/0x0
input: SynPS/2 Synaptics TouchPad as /class/input/input1
psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 1
Synaptics Touchpad, model: 1, fw: 5.9, id: 0xa54ab1, caps: 0x804713/0x0
input: SynPS/2 Synaptics TouchPad as /class/input/input2
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 16 (level, low) -> IRQ 16
Yenta: CardBus bridge found at 0000:00:10.0 [1524:1411]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:10.0, mfunc 0x00000202, devctl 0x44
i2c-sis96x version 1.0.0
Yenta: ISA IRQ mask 0x0878, PCI irq 16
Socket status: 30000006
sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0xe600
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
Adding 176672k swap on /dev/hda7. Priority:-1 extents:1 across:176672k
EXT3 FS on hda6, internal journal
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
NTFS volume version 3.1.
NTFS-fs warning (device hda5): load_system_files(): Unsupported volume flags 0x4000 encountered.
NTFS-fs error (device hda5): load_system_files(): Volume has unsupported flags set. Mounting read-only. Run chkdsk and mount in Windows.
hda: dma_timer_expiry: dma status == 0x21
hda: DMA timeout error
hda: dma timeout error: status=0xd0 { Busy }
ide: failed opcode was: unknown
hda: DMA disabled
ide0: reset: success
device eth1 entered promiscuous mode
pccard: CardBus card inserted into slot 0
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
************************************************************************
eth2: resetting device...
eth2: uploading firmware...
eth2: firmware version: 1.0.4.3
eth2: firmware upload complete
eth2: interface reset complete
************************************************************************
tcpdump uses obsolete (PF_INET,SOCK_PACKET)
device eth0 entered promiscuous mode
device eth0 left promiscuous mode


Reply to this message