Kismet Wireless

Kismet Forums

 

Posted by:EbilPhish
Subject:kismet_drone on a D-Link g604t
Date:18:58:55 16/05/2006

I grabbed the wrt54g mips build from the download page since g604t has the same cpu.

I belive the wireless card is a ACX111.

When running i get the following error:
-----------------------
Using alternate config file: kismet_drone.conf
Suid priv-dropping disabled. This may not be secure.
No specific sources given to be enabled, all will be enabled.
Disabling channel hopping.
Source 0 (Kismet-Drone): Enabling monitor mode for acx100 source interface wlan0 channel 6...
FATAL: channel get ioctl failed 1:Operation not permitted
------------------------


ifconfig give me:
------------------
br0 Link encap:Ethernet HWaddr 00:11:95:A0:0F:A9
inet addr:10.1.1.1 Bcast:10.255.255.255 Mask:255.0.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 ASYMMTU:1500
RX packets:175524 errors:0 dropped:0 overruns:0 frame:0
TX packets:166739 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:52631459 (50.1 Mb) TX bytes:107504111 (102.5 Mb)

br1 Link encap:Ethernet HWaddr 00:00:00:00:00:00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 ASYMMTU:1500
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

eth0 Link encap:Ethernet HWaddr 00:11:95:A0:0F:A9
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 ASYMMTU:1500
RX packets:175608 errors:0 dropped:0 overruns:0 frame:0
TX packets:166592 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:52647961 (50.2 Mb) TX bytes:107444485 (102.4 Mb)
Base address:0x2800

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1 ASYMMTU:0
RX packets:36 errors:0 dropped:0 overruns:0 frame:0
TX packets:36 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:9134 (8.9 kb) TX bytes:9134 (8.9 kb)

nas0 Link encap:Ethernet HWaddr 00:11:95:A0:0F:A9
inet addr:<MY INTERNET IP> Bcast:<MY INTERNET BCAST> Mask:255.255.255.252
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 ASYMMTU:1500
RX packets:156578 errors:1 dropped:0 overruns:0 frame:0
TX packets:162355 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:103870065 (99.0 Mb) TX bytes:48910796 (46.6 Mb)

wlan0 Link encap:Ethernet HWaddr 00:11:95:A0:0F:AA
UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 ASYMMTU:15
00
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:23 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:4110 (4.0 kb)
----------------------------------

My config file:
---------------------------
version=2005-06-R1a
servername=dlink
tcpport=3501
allowedhosts=10.1.1.1/24
maxclients=5
source=acx100,wlan0,Kismet-Drone
----------------------------

If i set eth0 then i get the following message instead.
FATAL: Failed to get SSID 122:Operation not supported

This is using the stock linux build that comes with the g604t not openWRT. As such the drivers for the wireless are the origionals, im not sure if that means they are offical drivers and diffrent drivers to the ones kismet is expecting or if they are the same ones as the sourceforge ones. Ive tried the other options for kismet sources however none of them worked.

Because this is a modem i have very limited tools avilable to use. Anything else i need to compile for MIPS which I havn't figured out how to do yet.

Some information about dlink-g604t here: http://www.seattlewireless.net/index.cgi/DlinkDslG604t#head-ccdf47ba5e49445b9e1d628180fb95c584d4b7e9


Reply to this message